Email marketing still proves to be one of the most effective forms of marketing available today. According to Direct Marketing email marketing, ROI of 4300%. Below are email marketing terms you're most likely to come across as you deal with email marketing.
A/B split: This refers to a method of testing your list for best results. First, your list is split into two, with every alternate name going to a list. Then, a different email is sent to each list. The objective is to measure which subject line, creative, and message have higher conversion rates.
Above the fold: Above the fold is an old newspaper term; it refers to the top half of the paper you see on a newsstand that shows the top story. This term has been adopted in email marketing to describe the top 1/3 of an Email that's viewable when the message is opened without scrolling. Your most valuable content should be in this area, as it is considered more valuable because the reader sees it first.
Acceptable Spam Report Rate: Your email list subscribers have the option to report your messages as SPAM if they don’t want your email; an acceptable spam report rate is the rate at which your email campaign recipients can report you as SPAM. Anything over 0.1% (1 report per 1000 emails) will get a warning.
Acceptance Rate: This is the percentage of email messages accepted by your recipient's mail servers. Even that your email has been accepted, it can still be flagged as spam and will never reach your recipient's inbox.
Acquisition cost: This is the cost to generate one lead or one customer that depends on the campaign's objective. This is calculated by dividing the total cost of the email campaign divided by the number of leads, subscribers, or customers generated.
Autoresponder: Event-triggered email message sent, can be set up to send new subscriber welcome message when a lead is converted by filling a form on a landing page, or eCommerce transactions, etc. Autoresponders can be as simple as a single message or an advanced workflow that sends a series of email marketing campaigns.
Block: ISP's servers block emails from domains and IP addresses that have been reported as spam.
Bounce Rate: The rate at which your emails are not delivered. This can be because of many reasons, such as invalid email, mailbox full, etc. Therefore, it is important that you track your bounce rate.
Call to action: To engage and convert your subscribers, your email message should have a call-to-action that clearly defines the action to take next.
CAN-SPAM: The law that sets the rules for commercial email, establishes requirements for commercial messages, gives recipients the right to have you stop emailing them, and spells out tough penalties for violations.
Clickthrough rate (CTR): Total number of clicks on links in your email message divided by the total number of emails sent.
Conversion Rate: The percentage of recipients who respond to your call-to-action in a campaign either by filling in a form with their information or downloading content, watching a video, etc.… Conversion rate is your metric for the success or failure of your promotion/campaign.
Double Opt-In: This is the advised method of building an email list since it asks subscribers to confirm their subscription following the instructions in a follow-up email. This is done to ensure that a subscriber is a real person who wants to join this mailing list.
Dynamic content: Email content that changes from one recipient to the next based on the interests or past behavior of the viewer.
Email Campaign: A single email or series of lead nurturing emails designed to accomplish an overall marketing goal.
Email Filter: A technique used to block email based on the sender, subject line, or email content. The increase in email filters has forced email marketers to find ways of getting past the filters. Personalization is the best way.
Event-triggered email: Pre-programmed messages sent automatically based on an event such as shopping cart abandonment, birthday, click on a call to action in a previous email campaign, a tweet with a specific #hashtag, etc.
Footer: The bottom of your email contains static information. Usually, the footers are home to contact information, address, disclaimer, and an unsubscribe link.
Grey-listing: An anti-spam technique that has the mail receiving server returns a failure code that says the mail should be retried later, with the hope that spammers would not make further attempts.
Hard Bounce: Hard bounce is the failed delivery of an email due to a permanent reason like a non-existent, invalid, or blocked email address. Hard bounce emails should be removed from your list.
HTML message: Email message containing HTML to add color, fonts, embed images and videos, and hyperlinks.
List Segmentation: The more information you have about each person on your email list, the better your email segmentation becomes. Information you are looking for is the age range, gender, interests, social profiles, industry, etc. A segmented list means a more targeted and relevant email campaign. Thus a higher response rate and fewer unsubscribes and spam reports.
Open Rate: The percentage of emails opened in an email marketing campaign, or the percentage opened of the total number of emails sent. This is a critical metric because it gives you an indication of the success of your email subject line. Was it exciting enough and therefore opened?
Opt-in: When a person permits a specific company to send them an email.
Opt-out: A specific request from an email recipient to unsubscribe from the email list.
Personalization: This works parallel to your list segmentation. Personalized emails containing the information you know about the recipient will increase the open and conversion rates.
Plain text: Text in an email message that includes no formatting code. See HTML.
Preview Text: Some email clients (Gmail, Outlook, iPhone, Windows Mobile 7) will display a portion of your preheader text as “preview.” This text is what the user sees before opening your email.
Rich Media: Rich media emails usually have high open and click-through rates. Remember, though, rich media emails require more bandwidth and are not compatible with all email clients and devices. So make sure before you send an email with rich media to only send it to a segmented list based on the recipient's email client and device.
Signature: An e-mail signature is a block of text appended to the end of an e-mail message you send. Generally, a signature is used to provide the recipient with your name, e-mail address, business contact information, or Web site URL
Single Opt-In: A single opt-in list is an email list sign-up process, Where the users don't need to confirm their subscription request.
Soft Bounce: A soft bounce is the failed delivery of an email due to a temporary issue, like a full mailbox or an unavailable server.
Spam: Irrelevant or unsolicited messages sent over the Internet, typically to large numbers of users, for advertising, phishing, spreading malware, etc.
Test: Always send a test email to your testing team before it goes out to your full list. Always. Test: A necessary step before sending an email campaign or newsletter. Many email clients permit you to send a test email before sending a regular email newsletter or solo mailing, in which you would send one copy of the message to an in-house email address and then review it for formatting or copy errors or improperly formatted links. Email marketers should also send a test campaign to a list of email addresses not in the deployment database to determine likely response rates and how well different elements in the message perform.
Transactional emails: Are sent to one person as a result of an action triggered by the user. These are automated notifications such as welcome emails, shipping notices, order confirmations, password reminders, purchase receipts, etc.
Unsubscribe Link: Every email must have an unsubscribe link to click on and follow instructions. Make sure that it is obvious where this link is in all of your emails. Emails without unsubscribing options are commonly considered spam.
Allowlist: Rather than listing IP addresses to block, an allowlist includes IP addresses that have been approved to deliver an email to a recipient.
I hope you find these useful and helpful.